您好,欢迎来到61ic! | [登录] [注册] 忘记密码 | 设为首页 帮助
 . 网站首页 . 业界新闻 . 设计中心 . 移动技术 . TI专栏 . ADI专栏 . FPGA专栏 . 代码工厂 . 官方商城 . 
 . 活动专区 . 新品快递 . 解决方案 . 前沿科技 . TI资源 . ADI资源 . FPGA资源 . 下载中心 . 产品展示 . 
加入收藏
付款方式
联系我们
您现在的位置: 61IC电子在线 >> 解决方案 >> 消费电子 >> 其它 >> 正文
  [组图]Atmel SAM V71 32位ARM Cortex-M7 MCU开发方案           ★★★ 【字体:
Atmel SAM V71 32位ARM Cortex-M7 MCU开发方案
作者:Atmel    文章来源:Atmel    点击数:    更新时间:2015-4-13    
Atmel公司的SMART SAM V71是32位基于ARM Cortex-M7处理器和浮点单元(FPU)的高性能MCU,工作频率高达300MHz,高达2048KB闪存和384KB多端口SRAM,外设包括支持IEEE1588, 802.1Qbb, 802.3az, 802.1AS和 802.1Qav的以太网MAC,高速USB器件和主接口,MediaLB器件接口,图像传感器接口,用于SDIO/SD/MMC的高速MCI接口,外接总线接口以及静态存储器控制器等.主要用在汽车娱乐系统连接和音频处理等.本文介绍了SMART SAM V71主要特性和框图,SAM V71 Xplained Ultra评估板主要特性和电路图,材料清单和pcb元件布局图.

The Atmel® | SMART SAM V71 devices are members of a family of AutomotiveFlash microcontrollers based on the high-performance 32-bit ARM® Cortex®-M7processor with Floating Point Unit (FPU). These devices operate at up to300 MHz and feature up to 2048 Kbytes of Flash and up to 384 Kbytes of multiportSRAM. The on-chip SRAM can be configured as Tightly Coupled Memory(TCM) or system memory. A multi-port access to the SRAM guarantees aminimum access latency. The peripheral set includes an Ethernet MAC supporting IEEE1588, 802.1Qbb, 802.3az, 802.1AS and 802.1Qav, a high-speedUSB Device port and a high-speed USB Host port sharing an embeddedtransceiver, a MediaLB device interface, an Image Sensor Interface, a high-speedMCI for SDIO/SD/MMC, an External Bus Interface featuring an SDRAMController, and a Static Memory Controller providing connection to SRAM,PSRAM, NOR Flash, LCD module and NAND Flash. Additional peripheralsinclude three USARTs, five UARTs, three TWIs, one Quad I/O SPI, two SPIs, oneSSC, as well as two enhanced PWMs, twelve general-purpose 16-bit timers withstepper motor and quadrature decoder logic support, two CAN-FDs, one lowpowerRTT, one low-power RTC, two 12-bit ADCs, one 12-bit DAC and oneanalog comparator.

The SAM V71 devices have three software-selectable low-power modes: Sleep,Wait and Backup. In Sleep mode, the processor is stopped while all otherfunctions can be kept running. In Wait mode, all clocks and functions are stoppedbut some peripherals can be configured to wake up the system based onpredefined conditions. This feature, called SleepWalking™, performs a partialasynchronous wake-up, thus allowing the processor to wake up only when needed. In Backup mode, RTT, RTC and wake-up logic are running. In addition,in this mode, the device is able to meet the most stringent Key-Off requirementswhile retaining 1Kbyte of SRAM and wake-up on CAN.

To optimize power consumption, the clock system has been designed to supportdifferent clock frequencies for selected peripherals. Moreover, the processor andbus clock frequency can be modified without affecting processing on, for example,the USB, U(S)ART, ADC and Timer Counter.

The Event System allows peripherals to receive, react to and send events inActive and Sleep modes without processor intervention.

The SAM V71 devices are high-performance Automotive microcontrollers,targeting In-Vehicle Infotainment connectivity applications, combining a rich set ofinterfaces including Ethernet-AVB and advanced DSP capabilities particularlyuseful for audio processing.

SMART SAM V71主要特性:
l Core
̶ ARM Cortex-M7 running at up to 300 MHz
̶ 16 Kbytes of ICache and 16 Kbytes of DCache with Error Code Correction (ECC)
̶ Simple- and double-precision HW Floating Point Unit (FPU)
̶ Memory Protection Unit (MPU) with 16 zones
̶ DSP Instructions, Thumb®-2 Instruction Set
̶ Embedded Trace Module (ETM) with instruction trace stream, including Trace Port Interface Unit (TPIU)
l Memories
̶ Up to 2048 Kbytes embedded Flash with unique identifier
̶ Embedded Flash Controller
̶ Up to 384 Kbytes embedded Multi-port SRAM
̶ Tightly Coupled Memory (TCM) interface with four configurations (disabled, 2 x 32 Kbytes, 2 x 64 Kbytes, 2 x128 Kbytes)
̶ 16 Kbytes ROM with embedded Boot Loader routines (UART0, USB) and IAP routines
̶ 16-bit Static Memory Controller (SMC) with support for SRAM, PSRAM, NOR and NAND Flash
̶ 16-bit SDRAM Controller
l System
̶ Embedded voltage regulator for single-supply operation
̶ Power-on-Reset (POR), Brown-out Detector (BOD) and Dual Watchdog for safe operation
̶ Quartz or ceramic resonator oscillators: 3 to 20 MHz main oscillator with failure detection, 12 MHz or 16 MHzneeded for USB operations. Optional low-power 32.768 kHz for RTC or device clock
̶ RTC with Gregorian and Persian calendar mode, waveform generation in low-power modes
̶ RTC clock calibration circuitry for 32.768 kHz crystal frequency compensation
̶ High-precision 4/8/12 MHz factory-trimmed internal RC oscillator with 4 MHz default frequency for devicestartup. In-application trimming access for frequency adjustment
̶ Slow Clock Internal RC oscillator as permanent low-power mode device clock
̶ One 500 MHz PLL for system clock, one 480 MHz PLL for USB high-speed operations
̶ Temperature Sensor
̶ One dual-port 24-channel Central DMA Controller
l Low-Power Modes
̶ Sleep, Wait and Backup modes, with power consumption down to 3 μA in Backup mode
̶ Ultra-low-power RTC and RTT
̶ 1 Kbyte of backup RAM with dedicated regulator
l Peripherals
̶ One Ethernet MAC (GMAC) 10/100 Mbps in MII mode and RMII with dedicated DMA. IEEE1588 PTP framesand 802.3az Energy-efficiency support. Ethernet AVB support with IEEE802.1AS Time-stamping andIEEE802.1Qav credit-based traffic-shaping hardware support.
̶ USB 2.0 Device/Mini Host High-speed (USBHS) at 480 Mbps, 4-kbyte FIFO, up to 10 bidirectional endpoints,dedicated DMA
̶ 12-bit ITU-R BT. 601/656 Image Sensor Interface (ISI)
̶ Two Master CAN-FD Controllers with SRAM-based mailboxes, time- and event-triggered transmission
̶ MediaLB® device with 3-wire mode, up to 1024 x Fs speed, supporting MOST25 and MOST50 networks
̶ Three USARTs. USART0/1/2 support LIN mode, ISO7816, IrDA®, RS-485, SPI, Manchester and Modemmodes; USART1 supports LON mode.
̶ Five 2-wire UARTs with SleepWalking support
̶ Three Two-Wire Interfaces (TWIHS) (I2C-compatible) with SleepWalking support
̶ Quad I/O Serial Peripheral Interface (QSPI) with eXecute-In-Place feature to a dedicated AHB memory zone
̶ Two Serial Peripheral Interfaces (SPI)
̶ One Serial Synchronous Controller (SSC) with I2S and TDM support
̶ One High-speed Multimedia Card Interface (SDIO/SD Card/MMC)
̶ Four Three-Channel 16-bit Timer/Counters with Capture, Waveform, Compare and PWM modes, constant ontime. Quadrature decoder logic and 2-bit Gray Up/Down Counter for stepper motor
̶ Two 4-channel 16-bit PWMs with complementary outputs, Dead Time Generator and eight fault inputs per PWMfor motor control, two external triggers to manage power factor correction (PFC), DC-DC and lighting control.
̶ 32-bit low-power Real-time Timer (RTT)
̶ Real-time Counter (RTC) with calendar and alarm features
̶ Two ADCs, each supporting up to 12 channels with differential input mode and programmable gain stage,allowing dual sampling and hold at up to 2 Msps. Gain and Offset error Autotest feature.
̶ One 2-channel 12-bit 2 Msps DAC
̶ One Analog Comparator with flexible input selection, selectable input hysteresis
l Cryptography
̶ True Random Number Generator (TRNG)
̶ AES: 256-, 192-, 128-bit Key Algorithm, Compliant with FIPS PUB-197 Specifications
̶ Integrity Check Monitor (ICM). Supports Secure Hash Algorithm SHA1, SHA224 and SHA256.
l I/O
̶ Up to 115 I/O lines with external interrupt capability (edge- or level-sensitivity), debouncing, glitch filtering andOn-die Series Resistor Termination
̶ Five Parallel Input/Output Controllers
l Voltage
̶ Single supply voltage from 1.62V to 3.6V
l Automotive
̶ Qualification AEC-Q100 grade 2 ([-40℃ : +105℃] ambient temperature)
l Packages
̶ LQFP144, 144-lead LQFP, 20 x 20 mm, pitch 0.5 mm
̶ LFBGA144, 144-ball LFBGA, 10 x 10 mm, pitch 0.8 mm
̶ LQFP100, 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm
̶ TFBGA100, 100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm
̶ LQFP64, 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm
̶ TFBGA64, 64-ball TFBGA, TBD
̶ QFN64, 64-pad QFN 9x9 mm, pitch 0.5 mm, with wettable flanks

图1.SMART SAM V71 144引脚框图

The Atmel®| SMART SAM V71 Xplained Ultra evaluation kit is a hardwareplatform to evaluate the ATSAMV71Q21, and other Atmel ARM® Cortex®-M7-based microcontrollers in the SAM V70, SAM S70, and SAM E70 series.

Supported by the Atmel Studio integrated development platform, the kitprovides easy access to the features of the Atmel ATSAMV71Q21 andexplains how to integrate the device in a custom design.

The Xplained Ultra series evaluation kits include an on-board EmbeddedDebugger, and no external tools are necessary to program or debug theATSAMV71Q21.

The Xplained Pro extension kits offers additional peripherals to extend thefeatures of the board and ease the development of custom designs.

SAM V71 Xplained Ultra评估板主要特性:

• ATSAMV71Q21 microcontroller
• One mechanical reset button
• One power switch button
• Two mechanical user pushbuttons
• Two yellow user LEDs
• Supercap backup
• 12.0MHz crystal
• 32.768kHz crystal
• 2MB SDRAM
• 2MB QSPI Flash
• Built in Ethernet MAC with external IEEE 802.3az 10Base-T/100Base-TX Ethernet RMII PHY
• AT24MAC402 256KByte EEPROM with EUI-48™ address
• WM8904 low power stereo audio codec
– External PLL for precise clock generation
– Microphone jack
– Headphone jack
• ATA6561 CAN Transceiver
• SD Card connector with SDIO support
• Camera interface connector
• MediaLB connector
• Two Xplained Pro extension headers
• One Xplained Pro LCD header
• Coresight 20 connector for 4-bit ETM
• Arduino™ Due based shield connectors
• External debugger connector
• USB interface, device and host mode
• Embedded Debugger
– Auto-ID for board identification in Atmel Studio
– One yellow status LED
– One green board power LED
– Symbolic debug of complex data types including scope information
– Programming and debugging
– Data Gateway Interface: SPI, I2C, four GPIOs
– Virtual COM port (CDC)
• External power input (5-14V)
• USB powered


图2.SAM V71 Xplained Ultra评估板外形图

图3.SAM V71 Xplained Ultra评估板电路图(1)

图4.SAM V71 Xplained Ultra评估板电路图(2)

图5.SAM V71 Xplained Ultra评估板电路图(3)

图6.SAM V71 Xplained Ultra评估板电路图(4)

图7.SAM V71 Xplained Ultra评估板电路图(5)

图8.SAM V71 Xplained Ultra评估板电路图(6)

图9.SAM V71 Xplained Ultra评估板电路图(7)

图10.SAM V71 Xplained Ultra评估板电路图(8)

图11.SAM V71 Xplained Ultra评估板电路图(9)

图12.SAM V71 Xplained Ultra评估板电路图(10)

图13.SAM V71 Xplained Ultra评估板电路图(11)

图14.SAM V71 Xplained Ultra评估板电路图(12)

图15.SAM V71 Xplained Ultra评估板电路图(13)
SAM V71 Xplained Ultra评估板材料清单:

图16.SAM V71 Xplained Ultra评估板PCB元件布局图(顶层)

图17.SAM V71 Xplained Ultra评估板PCB元件布局图(底层)
详情请见:
http://www.atmel.com/Images/Atmel-44003-32-bit-Cortex-M7-Microcontroller-SAM-V71Q-SAM-V71N-SAM-V71J_Datasheet.pdf
http://www.atmel.com/Images/Atmel-42408-SAMV71-Xplained-Ultra_User-Guide.pdf

Atmel-42408-SAMV71-Xplained-Ultra_User-Guide.pdf
Atmel-44003-32-bit-Cortex-M7-Microcontroller-SAM-V71Q-SAM-V71N-SAM-V71J_Datasheet.pdf
文章录入:admin    责任编辑:admin 
  • 上一篇文章:

  • 下一篇文章: 没有了
  • 发表评论】【加入收藏】【告诉好友】【打印此文】【关闭窗口
    最新热点 最新推荐 相关文章
    Atmel SMART SAM4C32智能电网…
    Atmel ATA6616汽车LIN网络总…
    Atmel ATSHA204 SHA-256密码…
    Atmel SAM4S 32位ARM Cortex…
    Atmel RZRAVEN低功耗2.4GHz …
    Atmel ATA6843 汽车BLDC马达…
    Atmel AT32UC3C汽车级马达控…
    Atmel ATA5830低功耗UHF ASK…
    ATmega128RFA1:低功耗ZigBe…
    Atmel AT32UC3A EVK1105 32位…
      网友评论:(只显示最新10条。评论内容只代表网友观点,与本站立场无关!)
    站长:61 湘ICP备13001086号-2